Results 1 to 10 of 10
Thread: Stairwell
-
06-04-2006, 05:54 AM #1
Stairwell
In taking an overall view of the inside of this room, I notice my stairs to the basement are missing, I have the well opening labeled as OPEN BELOW. The stairs show in plan view (1st floor) Any Ideas that will get them to show? As you can see, its a bit drafty....I've noticed this a few times in other plans but never paid any mind to it , only cause at the time it did'nt matter. Now it does. Anyway , any suggestion welcome.
See Attached.
DougDoug Michel
General Contractor
Design & Build, New Jersey
Windows 7... 64 Bit,
X6 Build 16.1.1.9 X64 w/SSA
X5 Build 15.2.1.3 X64 w/SSA
X4 Build 14.3.2.2 X64 w/SSA
X3 Build 13.4.2.7 w/SSA
X2 Build 12.6.0.25 w/SSA
X1,V10,V9
Sketch Up Pro 8
AutoCad 2014
Adobe CS6 Design Premium
A Pool Cue , a Harley, a Hammer & a Camera
Good Isn't Enough... When Better is Possible.
-
06-04-2006, 06:22 AM #2
Doug
Use the cross section slider tool,cut off the top of the house..........
Allen Colburn Jr.
Pascoag RI 02859
Residential Design Drafting/Framer
Drafter for:
http://www.artformhomeplans.com/
Chief Architect X4
-
06-04-2006, 06:39 AM #3
Thanks much Al.. That worked great.....Any Idea why it doesn't show when the "Render Floor Overview" Tool is used? Just curious.
DougDoug Michel
General Contractor
Design & Build, New Jersey
Windows 7... 64 Bit,
X6 Build 16.1.1.9 X64 w/SSA
X5 Build 15.2.1.3 X64 w/SSA
X4 Build 14.3.2.2 X64 w/SSA
X3 Build 13.4.2.7 w/SSA
X2 Build 12.6.0.25 w/SSA
X1,V10,V9
Sketch Up Pro 8
AutoCad 2014
Adobe CS6 Design Premium
A Pool Cue , a Harley, a Hammer & a Camera
Good Isn't Enough... When Better is Possible.
-
06-04-2006, 03:58 PM #4Chief user since v-4
- Join Date
- Feb 2001
- Location
- Salem CT
- Posts
- 179
Doug, It did not work because the render floor overview tool is only designed to show what is contained on a particular floor. The stairway that you are referring to is on the lower floor. Anything below the floor platform is considered to be on the lower floor. Hope this clears it up for you, Bob
Robert Roraback
Roraback Building & Design LLC
729 West Road
Salem CT 06420
-
06-04-2006, 07:28 PM #5
Thanks Bob, Yes it does.
DougDoug Michel
General Contractor
Design & Build, New Jersey
Windows 7... 64 Bit,
X6 Build 16.1.1.9 X64 w/SSA
X5 Build 15.2.1.3 X64 w/SSA
X4 Build 14.3.2.2 X64 w/SSA
X3 Build 13.4.2.7 w/SSA
X2 Build 12.6.0.25 w/SSA
X1,V10,V9
Sketch Up Pro 8
AutoCad 2014
Adobe CS6 Design Premium
A Pool Cue , a Harley, a Hammer & a Camera
Good Isn't Enough... When Better is Possible.
-
06-05-2006, 01:59 AM #6
My render view picks up the basement stairs..
.........
Allen Colburn Jr.
Pascoag RI 02859
Residential Design Drafting/Framer
Drafter for:
http://www.artformhomeplans.com/
Chief Architect X4
-
06-05-2006, 03:36 AM #7
Try pulling the stairs toward you more ...out from under the raised floor, See if it works for you then. Mine doesn't work...hummmm
DougDoug Michel
General Contractor
Design & Build, New Jersey
Windows 7... 64 Bit,
X6 Build 16.1.1.9 X64 w/SSA
X5 Build 15.2.1.3 X64 w/SSA
X4 Build 14.3.2.2 X64 w/SSA
X3 Build 13.4.2.7 w/SSA
X2 Build 12.6.0.25 w/SSA
X1,V10,V9
Sketch Up Pro 8
AutoCad 2014
Adobe CS6 Design Premium
A Pool Cue , a Harley, a Hammer & a Camera
Good Isn't Enough... When Better is Possible.
-
06-05-2006, 05:39 AM #8Always learning
- Join Date
- Nov 2005
- Location
- Adelaide, Australia
- Posts
- 733
Allen: using render camera view
Doug: using render floor overview
Hope this clears the confusion.
PeterPeter Sveinsson
Bathroom Designer, Kitchen Designer, Builder
Adelaide, Australia
email: peter@brilliantsa.com.au
email: (alternative) icy@senet.com.au
Website: www.brilliantsa.com.au
X4 on Windows 7
-
06-05-2006, 05:55 AM #9
Yes, it does.......mine is the same then. I still think ya should be able to see the stairs with Render Overview. Thanks Peter
DougDoug Michel
General Contractor
Design & Build, New Jersey
Windows 7... 64 Bit,
X6 Build 16.1.1.9 X64 w/SSA
X5 Build 15.2.1.3 X64 w/SSA
X4 Build 14.3.2.2 X64 w/SSA
X3 Build 13.4.2.7 w/SSA
X2 Build 12.6.0.25 w/SSA
X1,V10,V9
Sketch Up Pro 8
AutoCad 2014
Adobe CS6 Design Premium
A Pool Cue , a Harley, a Hammer & a Camera
Good Isn't Enough... When Better is Possible.
-
06-05-2006, 12:56 PM #10
Peter
No,I get the camera names all screwed up.
No biggie.........
Allen Colburn Jr.
Pascoag RI 02859
Residential Design Drafting/Framer
Drafter for:
http://www.artformhomeplans.com/
Chief Architect X4