Results 1 to 7 of 7
Thread: Wall Snap
-
01-24-2014, 05:05 PM #1
Wall Snap
I have looked in the manual and can not figure out how to prevent a wall snapping issue. I have attached two pics to hopefully explain what im trying to do. Im sure its a simple setting. Im still in X-5
Thanks
RobRob Mathews, RN, CGR, NARI CR
Curb Appeal Renovations
CurbAppealRenovations.com
Keller, Texas
8.0 - X-6 User
Dell Alienware Aurora ALX, Win 7 Pro, 64 bit, I7-4960X, 16 GB RAM, Dual NVIDIA GeForce GTX 690 4GB Graphics Card Dual 27" Monitors
-
01-24-2014, 08:48 PM #2
Registered User Promoted
- Join Date
- Jun 2006
- Location
- Cobourg, Ontario
- Posts
- 206
In x10 there was a setting in the wall DBX for this length, 'unconnected min. wall length'
I don't see that in my X4.
A work around would be to cut the wall at joint and change its definition, or just use the reverse wall layers tool on one portion so it does not snap back to form the 90.
BruceBruce MacNeill, O.A.A.
X-4 Premier, Win7 Pro
-
01-26-2014, 08:50 AM #3
Thanks. I did not see any setting in the DBX. As for the wall break, the closest I could break the half wall from the wing wall was 11.75" which wont work. Even if I could break the wall, it would still leave a small portion in place. I have been using a poly-line solid and making it 5.5" wide (a framed 2x4 wall with Hardi and tile on both sides) and 41" high to simulate a shower half wall. See a few attached pics of my projects of this wall set back to allow for the wall cap not to over hang the end of the wing wall.
Rob Mathews, RN, CGR, NARI CR
Curb Appeal Renovations
CurbAppealRenovations.com
Keller, Texas
8.0 - X-6 User
Dell Alienware Aurora ALX, Win 7 Pro, 64 bit, I7-4960X, 16 GB RAM, Dual NVIDIA GeForce GTX 690 4GB Graphics Card Dual 27" Monitors
-
01-26-2014, 12:58 PM #4
Draw an Room Divider wall at 90d to the nib.
Drag the Room divider wall to locate the end of the nib.Glenn
Chief X5
www.glennwoodward.com.au
Windows 7 - Home Premium
Intel i7-920
Gigabyte GA-EX58-UD3R
6 Gb DDR3 1600MHz
EVGA GTX285 1GbDDR3
1TB Sata HD
-
01-26-2014, 05:00 PM #5
Registered User Promoted
- Join Date
- Jun 2006
- Location
- Cobourg, Ontario
- Posts
- 206
-
01-26-2014, 05:05 PM #6
X6 has a new wall type - "room divider"
it is another form of invisible wall
LewLew Buttery
Castle Golden Design - "We make dreams visible"
Lockport, NY
716-434-5051
www.castlegoldendesign.com
lbuttery at castlegoldendesign.com
CHIEF X5 (started with v9.5)
-
01-27-2014, 08:21 AM #7Perry
P.H. DESIGNS L.L.C.
Eastvale Calif.
Alienware, liquid cooled
Ver 10-"X6 x64 SSA
WIN 8.1 PRO 64 bit
Nvidia GTX780 3GB.
i7 920 2.67-- 12 GB Ram
40" led monitor