Results 1 to 15 of 32
Thread: Measuring Existing Wall Angles
-
02-23-2007, 06:55 AM #1
Measuring Existing Wall Angles
Does anyone have any tools that they can recommend for
measuring the angles of existing walls when doing remodels ?
The tool would need to be decently accurate.
LewLew Buttery
Castle Golden Design - "We make dreams visible"
Lockport, NY
716-434-5051
www.castlegoldendesign.com
lbuttery at castlegoldendesign.com
CHIEF X5 (started with v9.5)
-
02-23-2007, 08:01 AM #2
one tool no...but i've used a level, chalk line, square and a calculator.
-
02-23-2007, 08:08 AM #3
a level, chalk line, square and a calculator.
Oh my, not what I want to hear
LewLew Buttery
Castle Golden Design - "We make dreams visible"
Lockport, NY
716-434-5051
www.castlegoldendesign.com
lbuttery at castlegoldendesign.com
CHIEF X5 (started with v9.5)
-
02-23-2007, 08:12 AM #4
There's a big long plastic angle guage at Home Depot, not sure what it's called, but I've seen it, two sizes I believe.
George VanDusen, CPBD, CKD, CID
Phoenix Construction
www.phoenixconstruction.com
Contr. Lic. #268157
HOUZZ link: http://www.houzz.com/professionals/s...cramento%2C-CA
-Certified Professional Building Designer
-Certified Kitchen Designer
-Certified Interior Designer
-Engineering Contractor
-Building Contractor
-Plumbing Contractor
Since 1971
Chief X4, X5
MOBO ASUS Rampage III Black Ed.
PROC Intel Core i7-990X 4.22 GHz
MEMORY 12 GB Corsair
GRAPHICS ASUS GTX 590 3GB, Dual-GPU
MAIN DRIVE OCZ 480GB SSD.
STORAGE OCZ 960GB SSD.
OS Win7 Pro 64 bit.
-
02-23-2007, 08:48 AM #5
If you can get into a corner use a bevel square as shown the in picture below and set it to the wall angles. Then match it to something like a speed square and you should be able to get it within a few degrees...
B and D are bevel squares....Jim Rogers
Jim Rogers Timber Designs
Georgetown, MA, USA
email: jrsawmill@verizon.net
V9.54-V10.08a-VX1.5.4.17-VX2-VX3-VX4-VX5
-
02-23-2007, 08:50 AM #6
It's called the angle-izer.
I just bought one last night but it seems like it will be too big to get into some corners/angles etc.
If it had telescoping legs I think it might have worked.
I will probably be returning it.
LewLew Buttery
Castle Golden Design - "We make dreams visible"
Lockport, NY
716-434-5051
www.castlegoldendesign.com
lbuttery at castlegoldendesign.com
CHIEF X5 (started with v9.5)
-
02-23-2007, 11:01 AM #7Registered User Promoted
- Join Date
- May 2006
- Location
- Orangeville, Pa.
- Posts
- 1,227
I've been in house construction for over 30 yrs. What I found works best is to have a few straight edges of different lengths. Take the two longest ones you can use and put them in the corner with each one running along the two walls out of the corner. Then measure the distance between the outside ends of the two straight edges and calculate. This way you'll have the known length of all three sides of your triangle. The longer your straight edges the more accurate your angle will be.
Larry Sweeney
Designer/Builder/Restorations/Period Cabinetmaker since 1972
Chief X5, AutoCad 2010
Windows 7 Pro
Asus P8P67 Pro
Intel Core i7 2600k
8 GB DDR# 1600mhz
GTX 670
-
02-23-2007, 11:10 AM #8
Larry:
Thanks for the reply, but that's what I'm trying to avoid.
Having to use multiple tools and do calcs etc.
I'm at the client site and I'm trying to get the photos and dims and get out within 1 -2 hours, depending on the size of the project area.
LewLew Buttery
Castle Golden Design - "We make dreams visible"
Lockport, NY
716-434-5051
www.castlegoldendesign.com
lbuttery at castlegoldendesign.com
CHIEF X5 (started with v9.5)
-
02-23-2007, 12:18 PM #9Registered User Promoted
- Join Date
- May 2006
- Location
- Orangeville, Pa.
- Posts
- 1,227
Lew
Take a tape meausre and measure out a distance each way from a corner, make a mark and then measure the cross corner distance between the two marks. Then either calculate the angle or figure it out in cad when you can get to it.Larry Sweeney
Designer/Builder/Restorations/Period Cabinetmaker since 1972
Chief X5, AutoCad 2010
Windows 7 Pro
Asus P8P67 Pro
Intel Core i7 2600k
8 GB DDR# 1600mhz
GTX 670
-
02-23-2007, 12:41 PM #10
Understand your problem,
"Excuse me ma'am, do you have a ruler?"
Just looking around & found this. ?? just a shot.
http://www.amazon.com/o/ASIN/B000HDK...B0CXXJVWGGMQR2Cris Jones
Jones Drafting Service
(707)780-3075
http://www.jonesdrafting.com
NorCal (Northern California)
(Residential-New,Addition & Remodel)
"It's your house, not mine."
CA X1
-
02-23-2007, 01:36 PM #11
That's it !!!!
That's what I'm looking for
I'll be placing the order soonest.
I was thinking of using a Sliding T-bevel with a protractor but that
was looking cumbersome, hence my posting here.
That combol was going to be $17 and the Digital Denali is $30
and less hassle and should therefore be faster and easier to use.
Not sure if it can handle wall lengths < 11 inches tho, but you can't have everything, or can you
Thanks
LewLew Buttery
Castle Golden Design - "We make dreams visible"
Lockport, NY
716-434-5051
www.castlegoldendesign.com
lbuttery at castlegoldendesign.com
CHIEF X5 (started with v9.5)
-
02-23-2007, 03:08 PM #12Registered User Promoted
- Join Date
- May 2006
- Location
- Orangeville, Pa.
- Posts
- 1,227
Lew
The thing you have to watch out for when using a protractor with short sides is that you can get a very inaccurate reading at times. Specially if the walls are sheetrock. I've seen many inside corners with a buildup of spackling compound that could change your angle reading by many degrees. So be careful, the longer your protractor sides the more accurate the angle.Larry Sweeney
Designer/Builder/Restorations/Period Cabinetmaker since 1972
Chief X5, AutoCad 2010
Windows 7 Pro
Asus P8P67 Pro
Intel Core i7 2600k
8 GB DDR# 1600mhz
GTX 670
-
02-23-2007, 05:08 PM #13Originally Posted by lgswe
Oh yeah...I do this too... I do this for laying out new construction too.
-
02-23-2007, 06:40 PM #14The Home Doctor
- Join Date
- May 2003
- Location
- Littleton, Colorado
- Posts
- 578
This is another good quality tool
http://www.amazon.com/s/ref=nb_ss_hi...&Go.y=14&Go=Go
It tells you the angle and also the mitre angle at the same timeDan Kerns
Using X5.
-
02-23-2007, 08:43 PM #15
thanks Dan:
I'll check them out, I haven't placed the order yet for the Denali.
LewLew Buttery
Castle Golden Design - "We make dreams visible"
Lockport, NY
716-434-5051
www.castlegoldendesign.com
lbuttery at castlegoldendesign.com
CHIEF X5 (started with v9.5)